Home
Register
Looking for a transmission cross member for dual exhaust that will work on a 1983 olds delta88
Thanks Sam 585-703-6030
Thanks Sam 585-703-6030
4 posters
transmission cross member
samjr1- Newbie (Tier 1)
- 5th Year AnniversaryCelebrating 5 years of being our member!
- Posts : 2
Join date : 2017-05-11
Boogie1468- Active Member (Tier 2)
- 5th Year AnniversaryCelebrating 5 years of being our member!
- Posts : 21
Join date : 2015-09-09
Location : Davisburg, Michigan, USA
Hi Sam. There were no factory crossmembers for dual exhaust until 1995 B bodies got the LT engine.
You can get a crossmrmber from a 95 or 96 impala or caprice. These are welded Stallings not made from tuning. The mounting provisions on the frame rails are not the same as yours. But adding brackets to your frame is not a terribly big job.
You can get a crossmrmber from a 95 or 96 impala or caprice. These are welded Stallings not made from tuning. The mounting provisions on the frame rails are not the same as yours. But adding brackets to your frame is not a terribly big job.
terry cronk- Freshman Member (Tier 3)
- 5th Year AnniversaryCelebrating 5 years of being our member!
- Posts : 249
Join date : 2015-08-19
Age : 77
Location : Mid-Michigan
I purchased this piece for my 1979 Caprice when installing either 700R4 or a turbo 350. Mine was 700R4.
https://www.ebay.com/itm/G-Force-Performance-RCB3-700-Trans-Crossmember-79-90-B-Body-700R4-4L60E/191786805782?hash=item2ca7626a16:g:cY8AAOSwMqBab5ou
Yes, its a lot of money but fits and super strong. The transmission mounts holes are about 3/4" back on the 700R4.
But the mount hole is slotted. And the outer holes are slotted and its heavy duty.
Good Luck.
https://www.ebay.com/itm/G-Force-Performance-RCB3-700-Trans-Crossmember-79-90-B-Body-700R4-4L60E/191786805782?hash=item2ca7626a16:g:cY8AAOSwMqBab5ou
Yes, its a lot of money but fits and super strong. The transmission mounts holes are about 3/4" back on the 700R4.
But the mount hole is slotted. And the outer holes are slotted and its heavy duty.
Good Luck.
GLHS60- Newbie (Tier 1)
- 10th Year Anniversary10 years of being a member on our forum!
- Posts : 4
Join date : 2013-10-24
I tried to put one of these on my 1981 with TH 350 but was unsuccessful.
The angle it was on would not fit my frame without serious modification.
For me the bigger problem was the TH 350 trans wouldn't clear the trans mount "pocket" in the crossmember.
I added another hump in my stock crossmember to allow dual exhaust.
I only tried one crossmember from a 1996 Impala, others may be different.
Thanks
Randy
The angle it was on would not fit my frame without serious modification.
For me the bigger problem was the TH 350 trans wouldn't clear the trans mount "pocket" in the crossmember.
I added another hump in my stock crossmember to allow dual exhaust.
I only tried one crossmember from a 1996 Impala, others may be different.
Thanks
Randy
Boogie1468 wrote:Hi Sam. There were no factory crossmembers for dual exhaust until 1995 B bodies got the LT engine.
You can get a crossmrmber from a 95 or 96 impala or caprice. These are welded Stallings not made from tuning. The mounting provisions on the frame rails are not the same as yours. But adding brackets to your frame is not a terribly big job.
